Is Your Business Network Cabling Ready for Wi-Fi 7?

200+ Articles published
5 IT topics covered
20+ Years of IT expertise
CE+ Cyber Essentials Plus
Share
In This Article
    Speedster IT
    Want IT That Just Works?

    Unlimited, proactive IT support from a team who answers the phone.

    Explore IT Support

    Why London Businesses May Need to Rethink Their Cabling for Wi-Fi 7

    Wi-Fi 7 access points are now widely available, and many London businesses are planning upgrades. But Wi-Fi is only wireless for the last few metres. Every access point still plugs into a cable, and that cable plugs into a switch.

    If the cabling or switch behind a new access point can’t keep up, you won’t get the speed you paid for. That’s why our Network Cabling & Structured Cabling London team checks the wired network before any Wi-Fi 7 upgrade, and why our Ubiquiti Experts London plan the access points and switching together.

    Who is this guide for?

    This guide is for office managers, business owners and IT leads who are thinking about Wi-Fi 7, moving office, or refurbishing a floor. You don’t need to be technical. We explain what to check, and when replacing cabling is genuinely worth it.

    What Is Wi-Fi 7?

    Wi-Fi 7 is the common name for the IEEE 802.11be standard. It builds on Wi-Fi 6 and 6E with:

    • Wider channels: up to 320 MHz in the 6 GHz band, where available.
    • 4096-QAM: packs more data into each transmission when the signal is strong.
    • Multi-Link Operation (MLO): devices can use more than one band at once for speed and reliability.
    • More capacity and lower latency: better for busy offices, video calls and cloud apps.

    Will my devices benefit straight away?

    Only devices that support Wi-Fi 7 get the full benefit. Older laptops and phones still connect, at their own speed. Most offices upgrade access points first, then gain more as staff devices are replaced.

    Why Faster Wi-Fi Puts More Pressure on Network Cabling

    Think of your network as a chain:

    Internet → firewall → switch → network cable → access point → Wi-Fi device

    Data can only move as fast as the slowest link in that chain. A Wi-Fi 7 access point can serve many users at once, so the cable feeding it carries far more traffic than before.

    What is a multi-gigabit uplink?

    The uplink is the cable between the access point and the switch. Many older offices run these at 1 Gbps. Enterprise Wi-Fi 7 access points usually have faster ports, typically 2.5, 5 or 10 Gbps, so they aren’t held back by a 1 Gbps connection. To use those speeds, the switch port and the cable both need to support them.

    Does the switch matter as much as the cable?

    Yes. A perfect Cat6A run plugged into a 1 Gbps switch port still runs at 1 Gbps. Cabling, switch ports and switch uplinks need to be planned together.

    Is Cat6 Good Enough for Wi-Fi 7?

    Often, yes, but it depends on the length and quality of each run.

    • Cat6 supports 1, 2.5 and 5 Gbps over the standard 100 metre channel in most installations.
    • Cat6 supports 10 Gbps only over shorter runs, typically up to around 55 metres, depending on the installation.
    • Cat6A supports 10 Gbps over the full 100 metre channel.

    So if your access points use 2.5 or 5 Gbps uplinks and your Cat6 runs are in good condition, you may not need new cabling. If you want 10 Gbps to access points on long runs, Cat6A is the safer choice.

    Why do so many new installations use Cat6A?

    Cat6A handles 10 Gbps at full length, copes better with higher-power PoE, and gives more headroom for future access points. The cost difference is usually small next to the labour of re-cabling an office later, which is why we often recommend it for new fit-outs.

    Wi-Fi 7 Isn’t Just About Speed. Don’t Forget PoE

    Most access points are powered through the network cable using Power over Ethernet (PoE). Wi-Fi 7 access points tend to need more power than older models, because they run more radios and faster ports.

    • PoE+ (IEEE 802.3at): up to 30 W per switch port.
    • PoE++ (IEEE 802.3bt): up to 60 W or 90 W per switch port, depending on the type.

    Some Wi-Fi 7 access points run with reduced features on PoE+, and need PoE++ for full performance. Always check the access point’s power requirement before choosing switches. For cameras or door access further than 100 metres away, see UniFi Long-Range PoE Switching: Power Devices up to 800 Metres Away.

    Work With Speedster IT

    Want IT support that actually works?

    Talk to us about how your IT is supported today, and what a managed IT partner should be taking off your plate.

    Talk to Our Team

    What is a switch power budget?

    Every PoE switch has a total amount of power it can share across its ports. If you plug in more power-hungry devices than the budget allows, some ports won’t get enough. We size switches so every access point, camera and phone gets the power it needs.

    Do cable bundles and heat matter?

    Yes. Sending more power through large bundles of cable makes them warmer, which can reduce performance. Good cable choice, sensible bundle sizes and proper routing all help, and Cat6A’s thicker conductors cope better with higher power. Our article on PoE++ Explained goes into this in more detail.

    Where should Wi-Fi 7 access points go?

    Wi-Fi 7’s 6 GHz band doesn’t travel as far through walls as 2.4 GHz. You may need access points in different places, or more of them. That means new cable runs, so it’s worth planning access point positions before any cabling is installed.

    What About Existing Cat5e Cabling?

    Cat5e isn’t automatically obsolete. It supports 1 Gbps over 100 metres, and in many cases 2.5 Gbps as well.

    When can Cat5e stay?

    • Desk points for PCs and phones that only need 1 Gbps.
    • Access point runs that test well at 2.5 Gbps, where that’s enough for the users on that access point.

    When does Cat5e become the limiting factor?

    • You want 5 or 10 Gbps to access points.
    • Runs are long, old, damaged or badly terminated.
    • You need PoE++ for high-power access points or cameras.
    • You’re refurbishing anyway, and the ceilings or floors are open.

    Cat5e vs Cat6 vs Cat6A for a New London Office

    Cat5eCat6Cat6A
    Bandwidth100 MHz250 MHz500 MHz
    Ethernet speed1 Gbps (2.5 Gbps in many cases)Up to 5 Gbps at 100 m; 10 Gbps on shorter runs10 Gbps at 100 m
    Typical useDesk points, phonesDesk points, most access pointsAccess points, cameras, smart buildings, new fit-outs
    Wi-Fi 7 access pointsLimitedGood, if runs test wellBest fit
    Higher-power PoEWorks, but more heat in bundlesWorks wellCopes best
    Future-proofingLowMediumHigh

    Which should we choose for a new office?

    For a new fit-out, we usually recommend Cat6A for access points, cameras and anything high-power, and Cat6A or Cat6 for desk points, depending on budget. If you’re moving premises, plan the cabling alongside the move itself. Our IT Relocation Services London team can co-ordinate both.

    Network Cabling for Smart Offices Is Changing Too

    Access points aren’t the only things on your network cabling any more. Many offices now run these over Ethernet:

    • CCTV cameras
    • door access control and video intercoms
    • occupancy sensors and environmental monitors
    • meeting room displays and booking panels
    • building systems such as lighting and heating controls

    Each one needs a cable, and many need PoE. Planning them into the same structured cabling saves running extra cables later. For more on this, see our UniFi Smart Building Solutions in London & Across the UK page.

    Do You Actually Need to Replace Your Network Cabling?

    Don’t guess. Get the existing installation checked first. A cabling survey looks at:

    • cable category on each run
    • link length
    • termination quality at sockets and patch panels
    • patch panel and cabinet condition
    • switch port speeds
    • PoE capacity and switch power budget
    • test results for each link
    • planned access point locations

    What happens after the survey?

    You get a clear picture of which runs can stay, which need re-terminating, and which need replacing. Often only part of an office needs new cabling, such as the runs to access points.

    Can we upgrade without disrupting the office?

    Usually, yes. Cabling work can be scheduled out of hours or in phases, so staff keep working. We plan the cut-over so access points and switches move across with minimal downtime.

    If you’re also choosing access points, our articles on UniFi Enterprise Wi-Fi 7 and UniFi Network 11 cover the kit itself, and our guide to Cisco Meraki MR series access points covers another popular option.

    Planning Wi-Fi 7 or Upgrading Your Office Network?

    Our network cabling services in London can assess your existing infrastructure and install the cabling you need for a faster, more reliable network. We handle the cabling, switches, access points and IT set-up as one project, so there’s one team responsible from start to finish.

    Call us on 0204 511 9111, email hello@speedster-it.com, or get in touch to book a cabling survey.

    Ready to Talk?

    Let’s fix this properly.

    Book a free consultation with one of our engineers and find out what better IT support actually looks like.

    Get In Touch